DJI Matrice 400
Quick Answer
The DJI Matrice 400 is a Matrice series DJI drone released in 2025, with 15.8 kg max, LiDAR + mmWave radar + vision, DJI video modes, 59min, 40 km FCC / 20 km CE, and O4 Enterprise Enhanced connectivity. Reboot Hub uses this page as a technical reference for specs, compatible OEM parts, common repair planning, and inspected pre-owned buying checks.
DJI Matrice 400 Comparison Snapshot
| Model position | Matrice series DJI drone, released 2025 |
| Flight profile | 15.8 kg max takeoff weight; 59min flight time |
| Camera profile | LiDAR + mmWave radar + vision |
| Signal profile | O4 Enterprise Enhanced; 40 km FCC / 20 km CE max range |
| Repair comparison | Compare shell, arm, ESC, flex cable, GPS, vision sensor, and gimbal availability before choosing between this model and another DJI drone. |
| Buying comparison | For pre-owned units, prioritize serial verification, battery health, gimbal calibration, flight test evidence, and warranty coverage over headline price alone. |
About the DJI Matrice 400
DJI Matrice 400 is DJI’s flagship enterprise flight platform. DJI lists a 9,740 g takeoff weight with two batteries, a 15.8 kg maximum takeoff weight, up to 6 kg payload, 59 minutes of flight time, 25 m/s maximum horizontal speed, IP55 protection, O4 Enterprise Enhanced transmission up to 40 km FCC or 20 km CE/SRRC/MIC, and obstacle sensing that combines vision, rotating and upper LiDAR, infrared ranging, and six-direction mmWave radar.
Technical Specifications
| Max Takeoff Weight (MTOM) | 15800 g |
| Max Flight Time | Up to 59 min (DJI stated test conditions) |
| Max Payload | Up to 6 kg (varies with altitude and battery level) |
| EU UAS Class | C3, C6 (C6 allows BVLOS under STS-02; parachute required) |
| Sound Power Level | 106 dB |
| Max Propeller Speed | 4050 RPM |
| Propeller | 2510F — 63.5×25.4 cm, 37.4 g each |
| Battery | TB100-20254-48.23 — 274×122×182 mm, 4720±20 g |
| Battery Station | BS100 Intelligent Battery Station |
| Remote Controller Battery | WB37 Intelligent Battery |
| Dual Gimbal Connector | M400 DGC — 158×320×115 mm, 231 g (optional) |
| Operator Modes | Dual Operator Mode supported |
| App | DJI Pilot 2 |
| Data Source | DJI Matrice 400 User Manual v2.0 + product listing (official) |
| Aircraft Weight | 5,020±20 g without batteries; 9,740±40 g with two TB100 batteries |
| Max Horizontal Speed | 25 m/s at sea level in still air |
| Max Flight Distance | 49 km under DJI no-wind test conditions |
| Ingress Protection | IP55 |
| Sensing | Omnidirectional color vision, rotating LiDAR, upper LiDAR, downward infrared range sensor, and six-direction mmWave radar |
| Transmission | O4 Enterprise Enhanced: 40 km FCC; 20 km CE/SRRC/MIC |
Common Failure Modes
Symptoms: Cracked shell, bent arm, loose landing gear, abnormal vibration, or visible crash damage.
Likely areas: outer shell, arms, landing gear, motor mounts
Inspect the airframe before powering on and verify the exact replacement part against the model variant.
Symptoms: Motor start failure, rough spin, propulsion warning, overheating, or unstable hover.
Likely areas: motor, arm wiring, ESC board, power connectors
Check for impact damage, cable strain, and water exposure before replacing boards or motors.
Symptoms: Camera shake, gimbal overload warning, tilted horizon, calibration failure, or no camera image.
Likely areas: gimbal assembly, vibration board, camera module, gimbal flex cable
Avoid forcing the gimbal by hand and recalibrate after any gimbal or camera service.
Symptoms: Positioning drift, obstacle sensing warning, compass or IMU calibration prompt, or unstable low-altitude hover.
Likely areas: vision sensors, IMU, GPS/GNSS board, sensor flex cables
Clean sensor windows and verify calibration after shell, sensor, or board replacement.
Repair Notes
Confirm the exact model, variant, error message, and visible damage before selecting parts. Do not substitute parts from a similar model without verification.
Remove the battery before opening the drone. Check for moisture, corrosion, and overheated connectors before reconnecting power.
Flex cables and coaxial cables are fragile. Route them without sharp bends and inspect connector locks before closing the shell.
After replacing gimbal, vision, GNSS, IMU, shell, arm, or propulsion parts, run the required calibration and perform a controlled low-altitude test.
DJI Matrice 400 Parts Library
Parts Atlas is being mapped from verified Reboot Hub inventory. Model specs and repair guidance are available below.
Browse verified partsCompatible Power & Accessories
Verified batteries, controllers, goggles, propellers, and accessories mapped from Reboot Hub inventory for this model.