DJI Matrice 300 RTK
Quick Answer
The DJI Matrice 300 RTK is a Matrice series DJI drone released in 2020, with 9 kg max, Payload, Zenmuse payload-dependent, up to 55 min (no payload), 15 km NCC/FCC / 8 km CE/MIC/SRRC, and OcuSync Enterprise connectivity. Reboot Hub uses this page as a technical reference for specs, compatible OEM parts, common repair planning, and inspected pre-owned buying checks.
DJI Matrice 300 RTK Comparison Snapshot
| Model position | Matrice series DJI drone, released 2020 |
| Flight profile | 9 kg max takeoff weight; up to 55 min (no payload) flight time |
| Camera profile | Payload; Zenmuse payload-dependent video |
| Signal profile | OcuSync Enterprise; 15 km NCC/FCC / 8 km CE/MIC/SRRC max range |
| Repair comparison | Compare shell, arm, ESC, flex cable, GPS, vision sensor, and gimbal availability before choosing between this model and another DJI drone. |
| Buying comparison | For pre-owned units, prioritize serial verification, battery health, gimbal calibration, flight test evidence, and warranty coverage over headline price alone. |
About the DJI Matrice 300 RTK
DJI Matrice 300 RTK is an enterprise drone platform for supported Zenmuse payloads. DJI lists up to 55 minutes of maximum flight time without payload; its published forward-flight specification with a 700 g load is 45 minutes at sea level. The aircraft is IP45 rated and uses OcuSync Enterprise transmission up to 15 km NCC/FCC or 8 km CE/MIC/SRRC in an unobstructed, interference-free setting.
Technical Specifications
| Dimensions (unfolded, excl. propellers) | 810×670×430 mm |
| Dimensions (folded) | 430×420×430 mm |
| Diagonal Wheelbase | 895 mm |
| Weight | 3600 g (batteries excluded) |
| Max Payload | 2700 g |
| Max Takeoff Weight | 9000 g |
| Max Horizontal Speed | 23 m/s (82.8 km/h) |
| Max Ascent / Descent Speed | 6 m/s ascent; 5 m/s descent; 7 m/s tilt descent |
| Max Forward Flight Time | 45 min (sea level, 700 g load) |
| Max Hover Time | 43 min (sea level, 700 g load) |
| Max Wind Resistance | 12 m/s (43.2 km/h) |
| Max Service Ceiling | 5000 m (2110 propellers); 7000 m (2195 high-altitude low-noise), takeoff weight ≤7 kg |
| Motor Model | 6009 |
| Propeller Model | 2110 |
| Ingress Protection | IP45 |
| GNSS | GPS + GLONASS + BeiDou + Galileo |
| Hovering Accuracy | ±0.1 m vertical / ±0.3 m horizontal (vision); ±0.1 m with D-RTK |
| Operating Temperature | -20°C to 50°C |
| Transmission | OcuSync Enterprise |
| Max Transmission Distance | 15 km (NCC/FCC); 8 km (CE/MIC/SRRC) |
| Supported Gimbals | Zenmuse XT2, XT S, Z30, H20, H20T, H20N, P1, L1 |
| Other Supported Products | CSM Radar, Manifold 2 |
| Remote Controller | DJI Smart Controller Enterprise (WB37 external battery) |
| App | DJI Pilot |
| Data Source | DJI M300 RTK User Manual v4.0 (official) |
| Max Flight Time (No Payload) | Up to 55 minutes under DJI maximum-flight-time test conditions, without payload. Compare the separate 45-minute/700 g forward-flight figure. |
| Official Public Specs | https://www.dji.com/support/product/matrice-300; https://dl.djicdn.com/downloads/matrice-300/20200610/M300_RTK_User_Manual_EN_0610_1.pdf (checked 2026-10-16) |
| Configured Weight with TB60 | Approximately 6.3 kg with two TB60 batteries and one downward gimbal; the 3.6 kg figure excludes batteries. DJI lists a separate 9 kg maximum takeoff weight. |
Common Failure Modes
Symptoms: Cracked shell, bent arm, loose landing gear, abnormal vibration, or visible crash damage.
Likely areas: outer shell, arms, landing gear, motor mounts
Inspect the airframe before powering on and verify the exact replacement part against the model variant.
Symptoms: Motor start failure, rough spin, propulsion warning, overheating, or unstable hover.
Likely areas: motor, arm wiring, ESC board, power connectors
Check for impact damage, cable strain, and water exposure before replacing boards or motors.
Symptoms: Camera shake, gimbal overload warning, tilted horizon, calibration failure, or no camera image.
Likely areas: gimbal assembly, vibration board, camera module, gimbal flex cable
Avoid forcing the gimbal by hand and recalibrate after any gimbal or camera service.
Symptoms: Positioning drift, obstacle sensing warning, compass or IMU calibration prompt, or unstable low-altitude hover.
Likely areas: vision sensors, IMU, GPS/GNSS board, sensor flex cables
Clean sensor windows and verify calibration after shell, sensor, or board replacement.
Repair Notes
Confirm the exact model, variant, error message, and visible damage before selecting parts. Do not substitute parts from a similar model without verification.
Remove the battery before opening the aircraft. Check for moisture, corrosion, and overheated connectors before reconnecting power.
Flex cables and coaxial cables are fragile. Route them without sharp bends and inspect connector locks before closing the shell.
After replacing gimbal, vision, GNSS, IMU, shell, arm, or propulsion parts, run the required calibration and perform a controlled low-altitude test.
DJI Matrice 300 RTK Parts Library
External
36 serviceable parts in this zone.
Circuit Boards
12 serviceable parts in this zone.
Flex Cables
7 serviceable parts in this zone.
Gimbal
5 serviceable parts in this zone.
Compatible Power & Accessories
Compatible batteries and accessories are being mapped from verified Reboot Hub inventory.